Powersports Protection Plus...

Home
Cover Features
Ready-Fit® Covers
Custom Fit Covers
Pack-Lite™ Half Covers
Pack-Lite™ Full Covers
Form-Fit® Covers
Scooter Covers
ATV Covers
Seat Shield
Watercraft Covers
Jet Bra
Cargo Tech Luggage
Cleaning Instructions
Warranty-Returns
Contact Us
Links

You can order direct from Covercraft - we are the manufacturer of these quality products!

Have a question?
Call toll-free,
M-F 9to5 CST
800-866-8621

 

 

 

 

 

Motorcycle, Scooter & ATV Cover Cleaning Instructions

Cover fabric performance can be severely affected by dirt that builds up on and within the material creating a “wicking” effect that actually helps pull water through the fabric, nullifying any water resistant properties the fabric may have had. Cleaning your cover will help to keep your motorcycle, scooter or ATV clean and also increase the service life of the cover.

For Pack Lite™ WeatherShield®, Form-Fit® and Flannel Covers ONLY:

NEVER...Clean a cover in a washer with a center agitator (OK if you don’t have a choice for WeatherShield® fabric covers).
NEVER...Use fabric softener.
DRY with Care... WeatherShield fabric & Form-Fit covers can be dried in a dryer with regular heat; flannel can be dried on low heat.

1 - Using a large commercial washer without agitator, wash the cover using 1/4 cup of Simple Green All-Purpose Cleaner. Put the cover in the washer and pour the cleaner in the tub after it’s filled with warm water or pour it directly in the machine (some wall mounted commercial units), then put in the cover and start the machine .
2 - Rinse the cover twice (2X) to remove all the cleaner.
3 - Dry in a dryer with regular or low heat...or hang to air dry.
 

For Urethane Coated Cycle, Scooter and ATV Covers ONLY:
Clean the cover while installed or lay on a flat surface.
1 - Mix one ounce Simple Green All-Purpose Cleaner per quart of warm water.
2 -Spray or sponge onto cover.
3 - Rinse with plain water (until no suds) and allow to air dry.  

PWC Cover Cleaning Instructions

Cover fabric performance can be severely affected by dirt that builds up on and within the material, creating a “wicking” effect where it actually helps pull water through the fabric, nullifying any water resistant properties the fabric may have had. Cleaning your cover will help to keep your PWC clean and to increase the service life of the cover.

NEVER...Clean a cover in a washer with a center agitator.
NEVER...Use fabric softener.
NEVER...Dry the cover in a dryer.

1 - Using a large commercial washer without agitator, wash the cover using 1/4 cup of Simple Green All-Purpose Cleaner. Put the cover in the washer and pour the cleaner in the tub after it’s filled with warm water or pour it directly in the machine (some wall mounted commercial units), then put in the cover and start the machine .
2 - Rinse the cover twice (2X) to remove all the cleaner.
3 - Hang to air dry (or you can install it on your PWC and let it dry).

You can also “spot clean” a cover on the PWC.
1 - Mix one ounce Simple Green All-Purpose Cleaner per quart of warm water.
2 -Spray or sponge onto cover and work it into the dirty area.
3 - Rinse with plain water (until no suds) and allow to air dry.

Simple Green is available in most world markets. If you have any questions, contact them at
1-800-228-0709 (USA) or visit their web-site www.simplegreen.com

If you have additional questions regarding the use or cleaning of your cover, please contact Covercraft Customer Service
at 1-800-866-8621 (USA) M-F, 9AM to 4PM CST, or by email at sales@covercraft.com

You can download the Cleaning Instructions by clicking on the link below

Motorcycle, Scooter & ATV

PWC Covers